Boiler Corrosion Prevention for Waste & Biomass Boilers

Corrosion Prevention in Biomass and Waste to Energy Boilers, Waste Incinerators

Life-Time Extension of Tube in Biomass and Waste to Energy Boilers, Waste Incinerators

Boiler Tube Coating in WtE & Biomass Boilers and Waste IncineratorsWe provide corrosion-resistant metal alloy protection for  Waste incinerators, biomass- and Waste-to-Energy Boilers. Typically designed for medium or large installations, these boilers produce steam by burning biomass, recycled biomass, or pre-treated industrial or urban waste. Fuel flexibility offers related cost reduction but results in boiler corrosion.

However, mixed fuel environments create extreme environments that can predispose equipment to damage. There is a wide variability of boiler design: horizontal grate, inclined grate, bubbling fluidized bed, circulating fluidized bed, etc. If the fuel contains plastics and other chemicals, Chlorine, Sulphur, and other alkali and heavy metals can generate, dramatically increasing the thickness loss rate through corrosion mechanisms.

Without proper preventative care, these conditions can lead to unexpected outages and high maintenance costs, reducing the efficiency and emission benefits of these boilers. However, the material improvement solutions offered by IGS can lead to a longer, better life for WtE boilers.

Boiler Corrosion Mechanisms in WtE and Biomass

Increasing efficiency of WtE boilers means increasing pressure and temperature inside the boiler tubes. The combination of new fuel types containing higher levels of corrosive agents with these higher temperatures and pressures can lead to material softening. Accelerated fireside boiler corrosion starts on the unprotected steel heat exchange surfaces of the super-heaters and erosion resistance declines.

Most corrosion protection mechanisms consist of generating a corrosion barrier on the base metal by forming an oxide layer. The challenge inside WtE boilers is that this layer is quickly eroded forcing the formation of another layer and consequently leading to the erosion-corrosion phenomenon. Erosion-corrosion thinning can happen quickly when harsh conditions are combined with soft or poor erosion resistance materials.

Mitigating Corrosion/Erosion in Waste to Energy and Biomass Boilers

 

WATCH WEBINAR GET WHITE PAPER

High-Temperature Chlorine Corrosion in WtE and Biomass Boilers

Chlorine species are highly responsible for high-temperature boiler corrosion in waste-to-energy and biomass sectors. Chlorine species dissolve in the flue gas during fuel combustion. The saturated chlorine salts condense at the relatively cold heat exchanger surfaces (cold trap). It can directly cause corrosion on metallic surfaces. The partial pressure of the chlorine salts near the steel surface increases at positions with high heat flux, which increases the reactivity of the chlorides driving corrosion.

The reaction between the chlorides and the iron on the steel surface results in iron chloride. The partial pressure of iron chloride gas is high. Consequently, it diffuses into the fouling where it contacts with oxygen to form iron oxide (Fe2O3 and Fe3O4). Sometimes chlorine corrosion is called active oxidation. Chlorine released diffuses back to the steel to cause a further corrosive attack. The result is an iron chloride layer directly on the tube surface, followed by a thicker layer of iron oxides, often penetrated by chloride salts.

That being said, the content of chlorine species in the flue gas is not as important for the intensity of the high-temperature corrosion as the content of specific chlorides inside the fouling and the heat flux density at the tube wall.

Hot Molten Salt Corrosion of WTE Boilers and Waste Incinerators

The hot molten salt fireside boiler corrosion process starts similarly to the high-temperature corrosion described above under the condition that the temperature of the tube surface is higher than the melting point of the precipitated salts so that salt melts directly on the metal surface. The resulting salt melts dissolve existing oxide layers, which lets the corrosive chlorine gas dissipate to the metal surface. Hot salt melts also change the structure of the fouling from a porous to a dense cover, trapping the iron chloride and closing it off from the gaseous oxygen thus supporting chlorine corrosion.

Pitting is an even more dangerous mechanism of the molten salts reacting as a liquid electrolyte directly with the steel and dissipating it.

Dew-Point Corrosion in WtE and Biomass Boilers

When the temperature of the flue gas decreases, gasses present in the environment reach saturation and droplets of liquid start to condense on solid surfaces. The saturation temperature depends on the load of the concerned gaseous species and (for sulfuric acid) on the humidity of the flue gas. The liquid electrolytes form wet spots on the surfaces, causing general corrosion and material loss in the form of pitting or almost uniform. In waste-to-energy plants the dew point corrosion is less common than in coal-fired plants, because SO3 reacts with chlorine species, making the formation of sulfuric acid less likely.

WtE Boiler Corrosion and Erosion Protection Experience

Refractory protection is the first defense against corrosive flue gases and can also have excellent erosion properties, but has limited heat exchange properties as the thermal efficiency is low. Refractory alloys can be used, but due to the excessive material costs and limited erosion resistance, the implementation of the surface protection layer is often a more cost-effective solution.

The use of thin ceramic coatings seems like an attractive approach, however, the thermal expansion mismatch and the fragility of such coatings make this solution unreliable. The coatings tend to crack and corrosion can develop underneath the protective layer which can then peel off.

HVTS vs Weld Overlay Cladding

Most of the weld overlay hard-facing alloys have a high propensity to cracking which can propagate into the base metal. Such solutions should be avoided on pressure parts but may be used on the mechanical structure.

One of IGS’s strengths is that we select our protective materials based on an in-depth analysis of the wastage mechanisms present in your equipment’s unique environment. Our solutions perform in the conditions of that exact boiler to mitigate corrosion and erosion. We apply our protective materials in a matter of days, during your planned turnaround periods. Our highly mobile global team of trained and experienced personnel provides the most convenient and effective solutions for your equipment.

Corrosion Resistant HVTS Metal Spray Coatings

We successfully use HVTS coating for decades in boiler corrosion applications. We have designed High Velocity Thermal Spray for applying a metal layer with very low porosity and sealability to better protect the base metal in high corrosion environments. This technology allows the use of solid or cored wire, enabling easy material modification compared to technologies depending on the market available solid wire. Since the process does not generate any dilution with the base metal, the quality of the coating remains uncompromised.

On-Site Coating Prevents Boiler Corrosion

IGS brings to bear decades of experience to bring you the best and most efficient technology for field application:

  • We work to reduce a critical path schedule as much as possible and comply with the schedules we commit to. IGS offers robust equipment and reliable technicians, with full compliance to all relevant EHS conditions and rules
  • We are familiar with the most difficult conditions in the most extreme environments.
  • Safety is a priority at IGS. Be it in the scaffolding, during clean up, or at any other time, we use a proactive, multi-level safety system to ensure a safe working environment for our employees and everyone around us.

Integrated Global Services Europe provides on-site thermal spray coating inside WtE and Biomass BFB boilers. We work in all countries of Europe, including the UK, Germany, the Netherlands, Italy, Switzerland, and France, from our operations center in the Czech Republic. We spray coatings in the United States, Middle East, Japan, South-East Asia, as well as Africa.

Leave us a note or start a chat with our operator to learn more about corrosion prevention in WtE and Biomass boilers.

Contact Us

  • Drop files here or